2nd Gen 5.9 Cummins Mads Smarty Programmer

Thumbnail Filmstrip of 5.9 Cummins Programmer Mads Smarty S-03 Images

* DTC (Diagnostic Trouble Codes) reader with

on-screen plain text interpretation of the codes.

* ABS programming for tire height adjustment.

* Upgrades through built in USB connector

* Automatic recovery of the ECM in case of an interrupted update.

* about 1.5 minutes required to update ECM

* Programmable speed limiter

Fast guide to Smarty's special Features

* CaTCHER software's inside

* Ten different performance levels

* Fastest download in the industry, a typical ECM update takes less

than two minutes

* ABS tire height updates in just seconds

* Not traceable in the stock setting. Smarty leaves no footprint

* Cold weather 3 Cylinder High Idle is enabled in all softwares

* Reads Diagnostic Trouble Codes in plain text

* No tools required, no fuses to pull

* USB built in for simple updates

* Most complete keyboard in the industry

* Reliable, it works off your OEM hardware

* Programmable Speed Limiter from 25 to 250 mph (in trucks of 2001

and 2002 the speed limiter is programmable in mph, older trucks have

only a speed adjustment

Fast guide to Smarty's softwares levels

SW# 0 : Half power .

SW# 1 : Fuel Saver

SW# 2 : Only more fuel and Boost fooling

SW# 3 : Like # 2 + added timing

SW# 4 : Soft CaTCHER no added timing

SW# 5 : Like # 4 + added Timing

SW# 6 : Mild CaTCHER no added timing

SW# 7 : Like # 6 + added Timing

SW# 8 : CaTCHER no added timing

SW # 9 : CaTCHER with Timing

Software number Zero,

About half the power of a stock software. Use it whenever reduced

power is desired or when you have to make sure that NO SMOKE

is produced .

Software number One,

The Fuel Saver software. Mpg gains vary, in most cases a + 2Mpg

has been reported. Please notice that the timing in this software is

rather aggressive. HEAVY TOWING is not recommended with this

software.

Software number Two,

This software increases the fuel delivered by the ECM and does the boost

fooling.

Software number :Three,

Same as software # 2 but timing has been

added.

CaTCHER softwares from number : Four to number Nine,

The even numbered softwares are identical to the odd numbered ones, except for the

timing. The softwares without added timing are intended for use with timing adding boxes.

The power gain at top Rpm with these softwares is almost identical. These softwares

differ greatly in HOW they get there. Than higher the software number then more

aggressive the throttle response from idle speed up. Aggressive to the point that the

softwares Eight and Nine can become difficult to handle on slippery roads. Please be

very careful when you use these softwares for the first time! It takes some time to

learn how to handle them.

The Mads Smarty S-03 Programmer is a diagnostic tool that can read trouble codes and provide on-screen interpretation. It can also be used to adjust ABS settings and upgrade the ECM through a built-in USB connector. The S-03 is fast and easy to use, with a recovery mode in case of interrupted updates. It's also programmed with a speed limiter for safety.

* DTC (Diagnostic Trouble Codes) reader with
on-screen plain text interpretation of the codes.
* ABS programming for tire height adjustment.
* Upgrades through built in USB connector
* Automatic recovery of the ECM in case of an interrupted update.
* about 1.5 minutes required to update ECM
* Programmable speed limiter

Fast guide to Smarty's special Features
* CaTCHER software's inside
* Ten different performance levels
* Fastest download in the industry, a typical ECM update takes less
than two minutes
* ABS tire height updates in just seconds
* Not traceable in the stock setting. Smarty leaves no footprint
* Cold weather 3 Cylinder High Idle is enabled in all softwares
* Reads Diagnostic Trouble Codes in plain text
* No tools required, no fuses to pull
*[...]