5.9 Cummins 3rd Gen MADS Smarty Programmer

Thumbnail Filmstrip of MADS Smarty S-06 POD Programmer - Power On Demand Images

Smarty S-06 POD / Smarty-S06 POD

* DTC ( Diagnostic Trouble Codes ) reader in

plain text interpretation

* ABS programming for tire height adjustment.

* Upgrades through built in USB connector

* Automatic recovery of the ECM in case of an interrupted update.

* 3.5 - 6 minutes required to update ECM depending on truck model

* Programmable speed limiter

* Power on Demand

Fast guide to Smarty''s special Features

*CaTCHER software's inside

*Ten different performance levels.

*Fastest download in the industry, up to three times faster than

competition, a typical ECM update takes about 3.5 to 5

depending on the truck model.

*ABS tire height updates in just few seconds.

*Not traceable in the stock setting. Smarty leaves no footprint.

*Manual High Idle is enabled in all softwares

With the Truck in park, activate cruise control. When dash light

illuninates hit set, this will activate high-idle. Use accell button on

steering wheel to set the rpm's in increments to the level you desire.

To turn the feature off, simply hit cancel on the cruise control or

tap the brake pedal.

*Reads Diagnostic Trouble Codes in plain text.

*No tools required, no fuses to pull.

*USB built in for simple updates .

*Most complete keyboard in the industry.

*Reliable, it works off your OEM hardware.

*Programmable Speed Limiter from 25 to 250 mph

*Power on Demand

Fast guide to Smarty's software levels

The horsepower settings. except #0, all other softwares have a modified "Torque management"

( TQM ). The throttle response is greatly improved but is set to a safe limit. With "Safe" Smarty

means safe for your tranny and rest of the driveline.

SW # 0 : Half power

SW # 1 : 30 Hp increase, with added timing .

SW # 2 : 60 Hp increase, no added timing.

SW # 3 : 60 Hp increase, with added timing.

SW # 4 : 90 Hp increase, no added timing.

SW # 5 : 90 Hp increase, with added timing.

SW # 6 : 160 Hp increase, no added timing.

SW # 7 : 160 Hp increase, with added timing.

SW # 8 : 210 Hp increase, no added timing.

SW # 9 : 210 Hp increase, with added timing.

Tested on stock trucks on a Mustang Dyno

Stock means just that. Stock! Even the air filters were stock...

The trucks were S T O C K, even the wastegate settings!

Smarty checked the "baseline" ( the stock truck Hp at the rear

wheels ) twice in a day in order to be sure about Smartys findings.

The above delared HP numbers are all rounded down to the

closest number. For example the 90 Hp file actually did 96 Hp.

That's a 90 Hp software for Smarty, not a 100. The 170 Hp was 174.

Power on Demand

100 power levels selectable in just one second during the driving! It's easy:

just type the preferred power level directly on Smarty keyboard, from 00 to 99.

That's all! For security reason, the truck waits that the throttle is released

before applying the new power level.

No trace is left in the ECM!

SmartyCR is the FIRST AND ONLY downloader that does not erase any of

the stored data in the ECM. Smarty does NOT leave any electronic footprints

in the ECM or any other electronic module in the truck. Smarty does NOT

set ANY codes once the ECM is set back to stock. Smarty does NOT need

to have fuses pulled.

No matter what the competition claims , in one way or another they're ALL detectable.

Smarty is NOT!

Yet, Smarty can not do one thing for you. Fix what others have broken. Smarty can not

restore a key on counter that another downloader has erased . Smarty can not fix VIN#

troubles caused by other products. If your Check engine / ABS light is on because another

product has screwed your ECM, Smarty can not fix it, the other guy HAS to...

ABS / Speedo recalibration

The tire height can be adjusted up to 44" in increments of 10 tenth of an inch

in just a couple seconds. Of course, Smarty needs to be VIN# locked to the

truck in order to get into the ABS adjustment section.

DTC Code reader

The name says it all.

You can read and erase codes. Codes are displayed also in plain English.

That's old news by now. Smarty S-03 was the first one to provide that

utility, others found the idea to be a good one too. ( Smarty does erase

ABS codes too but does not display them )

ECM update speed

Faster than anything else on the market! Again Smarty has done its homework

on the protocol. Less than 5 minutes. Three times faster than a Star-Scan

diagnostic tool or competitor.

Smarty has developed its own bootloader in order to not have to

pull fuses should an update become interrupted for any reason.

All you have to do is to turn the key off / key on Smarty does

everything else on it's own.

Updates

CaTCHER softwares as they are today are only a Starting Point.

Smarty S-06 POD / Smarty-S06 POD
* DTC ( Diagnostic Trouble Codes ) reader in
plain text interpretation
* ABS programming for tire height adjustment.
* Upgrades through built in USB connector
* Automatic recovery of the ECM in case of an interrupted update.
* 3.5 - 6 minutes required to update ECM depending on truck model
* Programmable speed limiter
* Power on Demand

Fast guide to Smarty''s special Features
*CaTCHER software's inside
*Ten different performance levels.
*Fastest download in the industry, up to three times faster than
competition, a typical ECM update takes about 3.5 to 5
depending on the truck model.
*ABS tire height updates in just few seconds.
*Not traceable in the stock setting. Smarty leaves no footprint.
*Manual High Idle is enabled in all softwares
With the Truck in park, activate cruise control. When dash light
illuninates hit set, this will activate high-idle. Use accell button on
steering wheel to set the rpm's in increments to the level you desire.
To turn the feature off, simply hit cancel on the cruise control or
tap the brake pedal.
*Reads Diagnostic Trouble Codes in plain text[...]